Graphic material from the Net. Hope I am not stepping on anybody's toes
Strange contraptions of complex engineering and somehow giving the general impression of charming clumsiness, helicopters have been there almost from the beginning of the industry. So goes too for the kit industry. I like to build one of them now and again, just for a change, and (I must admit) because they are usually easier to build than planes (gasp!). But why keep it simple, right? Let’s do a conversion to a civil passenger transport, completely modifying the fuselage of an existing kit. For that I acquired an Air-Craft Models resin aftermarket set that after some serious surgery should render the necessary changes to represent a Chicago Helicopter Airways Sikorsky S-58C.
Nice transparencies, but Italeri packed them with the rest, so of coarse there are several scratched that will need polishing. Hey, Italeri, how expensive is a plastic sleeve?Major parts detached, all cleaned up. Bonga-Bonga bits to the trash can:The aftermarket set, sturdy box to protect contents:Profusely illustrated instructions with added advice:Well-cast, no bubbles, no deformities, nice detail. So far so good. They don not have on catalog the one I want t build, so I purchased a similar one that includes flotation gear:
The interior walls are smooth and have some detail, and do not show the coarseness of other resin offerings:
The set includes photo-etched details and decals (the latter won't be used, as I will commission a particular set for the Chicago Helicopter Airways machine):
Masks, but others will need to be hand-made for the additional windows:
The resin parts are easily separated from their pouring blocks. The fuselage sides need all their cabin windows and doors opened. This is not an easy-peasy affair as the flash membrane that covers these openings (at least on my sample) is thick, so this is a multi-step, carefully and gradually approached business:
The resin is very nice to work with, and again no bubbles, no short pours, no warping. Good set.A caveat that came via Tim and Tom Kalina: The tail rotor in the Italeri kit "rotates" the wrong way, so those blades have to be cut-off, a metal pin inserted, and re-glued in the opposite direction. Thanks to them for this very important detail that completely escaped me, naive as I am, thinking that most kit manufacturers do their homework 🙄
A few vents are drilled:
The instructions have you cut the tail of the kit's parts:
The hub is also drilled:
et voilà:Some of the parts are glued and other are being prepared for airbrushing:Notice that I glued the tail halves. The kit's instruction want you to add the tail rotor at this time so it can lock on the washer that goes inside:
...which is stupid as any modeler knows, because it will hinder a number of other steps, painting included. More intelligent manufacturers came to other solutions to allow parts to rotate.
The holes for the LG legs need a bit of enlarging for a comfortable fit:
Some notes:
There is a photo-etched set for this helicopter but mostly applies to the military variants. The only really useful bits for me would have been the nose meshes, BUT, they require careful and clean surgery, and I will just simulate the effect. IF there was an afermarket engine set (with all the details, not just the engine), then I would have considered opening the nose and do the screens.
This civil version needless to say differs in many details from the kit, so it's mandatory to study photos. Even so, the five machines CHA had seem to differ among themselves in some details too, so one registration should be chosen, study and represented. Their decoration presents some variants too.
Preparing some parts for priming and base color:
The main rotor is assembled:
A coat of primer:
The kit's exhaust is discarded as these machines had extended ones. The resin aftermarket part is in turn substituted by a more realistic metal tube:
Some more painting and priming:
The task ahead is to provide the multiple windows for the cabin. They are too large for "window maker" liquid, so I usually do this by cutting and individually adjusting acrylic. Not a fun task. But first the cockpit so one can have the sense of accomplishing something:
There is a difference on my sample of about 1.5 mm between the two halves of the "floor". Hot water and careful bending corrected most of it, yet one side of the floor is noticeable thicker than the other, so some sanding will be needed. Good that I noticed this before installing the windows. The instructions recommend gluing the fuselage halves and then "slide-in" the cabin and cockpit, but dry-runs pointed out to some small amount of filing and sanding for them to have a comfortable fit that way:
There was a circular opening on the right nose half that was occluded from the interior (vent? access?). This is replicated. A P.E. rim will be added after painting:
Working on other nose details, light housing and beacon (dry fit):Here is my hobby-related package, bouncing back and forth between San Francisco and... San Francisco, and between San Francisco and Oakland. Thanks to the diligence of our Postal Service and AI. This is ONE of the several packages I tracked lately doing the same Mambo routine, uselessly, and being delayed because off automation and application of AI:
Good that I checked, but I wish I had done it before painting. All the seat ends need some sanding before gluing on the floor or they won't fit inside the resin fuselage:
The seats are dressed:
The corrected tail rotor is completed:
Main rotor completed. Nose and tail assembled, seams treated and primed:
The impeccable set from Arctic Decals has arrived:
The task of measuring, cutting and adjusting each individual window starts. The master is not very precise, so windows that should be equal sizes are not, making the task a little bit more challenging:
All windows are in:
As the resin halves are not a good match, work begins by using epoxy on the tail section...
...then superglue will be used in short sections until all the contact areas are aligned an secured.Instructions for the aftermarket addition tell you to slide the cabin and cockpit in after this step is completed. We'll see how it goes...
Some of the kit parts need to be added now. I started with the one that goes underneath the fuselage:
Then tried (dry-fit) all the others. The fit is not clean-cut, and the parts need some adjustments before they are glued, and putty later for sure, but nothing terrible:
The tail goes in. Again not a perfect match, but with work it should do:
A perfect day for modeling:A quick look at the fit of the interior was promising. It should be OK with a few small adjustments:
As this vent is louvered, and therefore maybe letting some sanding dust or airbrushed paint inside, I decided to blank it with two simple styrene shapes:
Part of the nose mods include the substitution of the kit's curved exhaust for a straight and longer one. A small box is made to support it and blank the empty interior. The louvered vent (now boxed too to avoid dust and airbrush paint in the interior) is seen behind:
The cabin and cockpit were slid-in as recommended with no issues (phew!). The modified louvered vent and rotor support were added, as well as the side cockpit windows:
In order to use the P.E. console provided in the aftermarket set for the canopy roof, you have first to erase the relief detail already present there. Unfortunately -as in the S.55- the manufacturer molded the wipers, which is a bad choice. The aft. mkt. set includes P.E. ones. The position of the inst.pan. on the nose is not well indicated on the instructions and the fit is completely vague to say the least. Trial and error will have to do.As with the recently built civil S.55, you can see underneath the fuselage two running battens, instead of the military detail that comes with the kit. Thus that part is not added, but the battens instead are added:
The nose is glued:
A dry fit of the canopy shows a reasonable fit with just narrow gaps to fill:The Eduard mask set will only serve for the canopy, as the aftermarket fuselage has different windows. Eduard sets are usually spot on, but this one isn't, being the cockpit's side windows masks rather larger than the parts themselves. The windows have double curvature, so Eduard made a double mask and apparently incorporated some "slack" that happened to be too much. Beware also that the slits on the masks -to help with curving them- can let paint through, so I added an extra piece of tape over the slits:
A couple more fixes and it should be ready for the white paint:
White paint on. I kept the horizontal stabilizer separated to facilitate painting of the other colors on it and the fuselage:
I have learned long ago not to airbrush at nigh time, since a combination of not-so-sharp-now eyesight and deceiving artificial lighting is conducive to mistakes. As I often do, I ignored my own advice and previous experience and proceeded to apply the slightly bluish grey color after masking the white areas...at night. Several things happened: firstly, I mixed the wrong hue tricked by the artificial lighting. Them (of course) my airbrush decided to misbehave -without my noticing until after the next morning- and produced a number of artistic sputters all over the model. The absolutely malign nature of hobby tools and materials is known to all modelers. The basterds wait for the minutest opportunity to ruin our precious work. So I had to wait for the paint to dry, and very carefully light-sanded the models with progressively fine grains. Thanks, me, for almost ruining a model, and add days to the completion of it, plus having to re-mix the paint to the proper shade. Now it waits for the correcting coat:
The re-paint seems to have gone well. Once the paint has dried the grey will be masked to apply the blue color. The doors are painted at this time time, as well as piece of decal paper to correct small things if needed:
Main colors on, masks off. The blue bands on the tail will be done with painted decal paper:
The aftermarket doors are assembled, trapping clear plastic between the inner and outer faces. Easier said than done, as superglue is involved:
Minor touch-ups and details picked up in color. The "screened" areas are given a wash:
The lower portion of the nose area was modified -as described during assembly- to reflect the civil version. Two home-made lenses are installed in guise of lights. The beacon will be added upon completion:
After applying the decals, more parts can be added (landing gear, stab, exhaust)
Now the cabin steps provided in the conversion set:
And underneath. As commented before, I deviated from the kit´s detail and included instead what I could see in photos of this particular helicopter:
A dry run of the main and tail rotor:
Many details still to be added: doors, tail beacon, wipers, tail blue bands, tail LE rungs, Pitot...
To be continued...







.png)

You’re lucky to have that resin kit. I had to kit bash my model.
ReplyDeleteIndeed, it solves a big problem and saves many hours of hard work. Your model is beautiful, though.
Delete